Book Appointment Now

Your washing machine was built to last 10 to 12 years. But in Austin, we replace them after 6 or 7 years because of preventable failures. Hard water, overloading, too much soap, and never cleaning the filter kill washers early.

We at Atlas Appliances Repair repair washers from Samsung, LG, Whirlpool, Maytag, GE, and Bosch every day. The expensive repairs we see are almost always caused by three simple maintenance mistakes that take 10 minutes to prevent.

Here are the 3 ways to add 5+ years to your washing machine’s life, straight from certified technicians.

If your washer already needs help, you can book a same-day tune-up or repair with Atlas Appliances Repair or call us directly at (512) 877-9421.

1. Clean What You Can’t See – The Filter, The Gasket, and The Dispenser

Most people have never cleaned their washing machine filter. Most don’t know it exists.

For front-load washers (Samsung, LG, Whirlpool, Maytag, Bosch):
You have a drain pump filter behind a small square door on the bottom front of the machine. This filter catches coins, hair ties, socks, lint, and bra wires. When it clogs, your washer won’t drain, won’t spin, starts to smell, and shows error codes like OE, ND, or 5C.

We pull golf balls worth of gunk out of these filters every week.

What to do: Every 3 to 4 weeks, place a towel under that door, open it, unscrew the filter cap slowly, and drain the water into a shallow pan. Remove all debris, rinse the filter under your faucet, and screw it back in. It takes 5 minutes.

Also, wipe the big grey rubber door gasket dry after every load. Pull back the fold and you will see black mold slime. That slime is what causes that mildew smell on your “clean” clothes. Wipe it with a dry cloth after each wash and leave the door wide open for at least 2 hours after a load so it dries completely.

For top-load washers:
You don’t have a pump filter you can access, but you have a fabric softener and detergent dispenser that gets clogged with hardened soap and softener. Pull the dispenser drawer completely out, soak it in hot water with vinegar, and scrub it with a toothbrush. Clogged dispensers cause detergent to not dissolve, which leaves white residue on clothes and burns out your inlet valves.

Once a month, run a hot empty cycle with 2 cups of white vinegar and 1/2 cup of baking soda, or use a washer cleaner tablet like Affresh. This dissolves hard water scale and soap scum inside the drum, hoses, and pump. In Austin, our hard water scale buildup is 3x worse than average and is the #1 reason washer pumps fail early.

2. Use Less Soap and Smaller Loads – Stop Overloading

These two habits cause more expensive repairs than anything else.

Using too much detergent:
More soap does NOT mean cleaner clothes. Modern washers are designed to use 1 to 2 TABLESPOONS of detergent per load, not a full cap. If you use a full cap of regular detergent in an washer, you create too many suds. The suds cushion the clothes so they don’t rub against each other to get clean. Your clothes come out still dirty.

Worse, excess suds overflow onto the motor and control board, causing corrosion and electrical failures. They also leave soap scum inside the outer tub that turns into black mold and clogs your drain pump.

If you have soft water and you see suds left at the end of a cycle, or if your clothes feel slimy, you are using way too much.

Rule: Use 1 tablespoon for small loads, 2 tablespoons max for large heavily soiled loads. Use only detergent. If you use pods, use ONE pod only.

Overloading:
Your washer’s basket is floating on 4 suspension rods and a bearing. When you stuff it full of 6 bath towels, 10 pairs of jeans, and a king-size comforter all at once, you exceed the weight limit by 20 to 30 pounds.

What breaks:

  • Suspension rods stretch and snap – $250 to $350 repair, causes banging and walking
  • Bearings grind and fail – $400+ repair, causes jet-engine loud noise on spin
  • Lid switch or door lock breaks from force – $150 to $220 repair
  • Belt burns and snaps – $160 to $240 repair

Rule: Load until the drum is 3/4 full, not packed tight. You should be able to fit your hand vertically above the clothes. For bulky items like comforters and blankets, wash one at a time on the Bulky cycle with extra water.

3. Check Hoses, Level, and Water Pressure

Replace your hoses before they flood your house.
The black rubber hoses that came with your washer from the factory will burst. It’s not if, it’s when. After 5 years, rubber deteriorates, especially in a hot Texas garage or laundry room. When a hose bursts, it dumps 4 gallons per minute onto your floor. We have seen $15,000 in flood damage from a $10 hose.

Replace them today with braided stainless steel hoses with auto-shutoff. They cost $25 to $40 at Home Depot and take 10 minutes to install. Turn off water, unscrew old, screw on new. While you are there, replace the small mesh inlet filters on the back of the washer. Austin’s hard water clogs them and starves the washer of water.

Level your washer properly.
If your washer is not level, it will walk, bang, shake violently, and destroy its suspension and bearings prematurely. Place a level front-to-back and side-to-side on top of the washer. Adjust the front feet up or down until it is perfectly level and all four feet are firmly on the floor with no rocking.

A walking washer is not normal. It means it is not level or the suspension is already damaged from overloading.

Don’t ignore slow fill or error codes.
If your washer takes a long time to fill, shows IE, 4C, or NF errors, or if your cold water is very slow, your inlet valve screens are clogged with hard water sediment. Clean them or call for service before the valve burns out from trying to open against pressure.

The Maintenance That Takes 10 Minutes and Saves You $400

If you do these three things monthly, your washer will easily last 12+ years:

  1. Drain and clean the pump filter, wipe gasket, leave door open.
  2. Use 1-2 tablespoons of HE detergent only, and never overload past 3/4 full.
  3. Check that hoses are stainless steel, washer is level, and run a hot vinegar clean monthly.

Most washers we condemn at 6 years old failed because these were never done. Most washers we see at 12 years old that still run perfectly had owners who did these basics.

Need a Professional Washing Machine Tune-Up?

Sometimes you need more than maintenance. If your washer smells, won’t drain, bangs loudly, leaks, or won’t spin, don’t let a small clog turn into a burned-out pump or control board.

Let the local washing machine experts handle it.


Want to add years to your washing machine?

The certified technicians at Atlas Appliances Repair offer same-day washing machine tune-ups, filter cleaning, drain cleaning, leveling, hose replacement, and full repairs for all brands – Samsung, LG, Whirlpool, Maytag, GE, Bosch, Kenmore.

We stock common parts like drain pumps, lid switches, door locks, suspension rods, and inlet valves on our trucks, give you upfront honest pricing, and warranty every repair.

Book online now at Atlas Appliances Repair or call us at (512) 859-5333 for fast, reliable washing machine service in Austin, Round Rock, Cedar Park, Pflugerville, Georgetown, Leander, Buda, Kyle and surrounding areas.

We will keep your washer running like new.

Call Now: (512) 859-5333 Call Now: 512-540-3897